RESOURCES

Energy harvesting vs battery backup in multi turn absolute rotary encoders: a technical comparison

Classification:

Knowledge

Release Time:

2026-11-11

Author:

Changchun Rongde Optics

Source:

1


Article overview

This guide compares battery backup and energy harvesting as ways to preserve the revolution count in a multi turn absolute rotary encoder. It covers operating principles, maintenance, speed and resolution limits, interface options, a selection procedure, and application cases for engineers who need to prevent position loss after a power failure.

A multi turn absolute rotary encoder reports shaft angle and total revolutions as one position value. The open question in 2026 is how it keeps that revolution count when the machine is switched off. Battery backup stores energy chemically in a small cell. Energy harvesting, as used in a Wiegand multiturn encoder, converts shaft motion into the energy needed for counting. Neither route is universally better. This guide compares both for U.S. automation and robotics engineers who worry about losing home position after an outage, and it closes with a selection procedure you can apply to your own axes.

Why does this matter so much? Because a lost count means re-homing, and on a vertical axis or a robot joint with a released brake, that is more than an inconvenience. Many readers also arrive here comparing a single-turn vs multi-turn encoder, so that distinction comes first.

Why power-off position retention matters in a multi turn absolute rotary encoder

A multi turn absolute rotary encoder has to keep counting shaft revolutions while the machine is unpowered, because axes can still move during shutdown, transport, or manual brake release. If the count is lost, the controller cannot tell turn 3 from turn 300, and the axis must be re-homed. Everything else in this comparison follows from that single requirement.

A multi turn absolute rotary encoder is a rotary position sensor that outputs a unique code for each angle within a revolution and also encodes the number of full revolutions. Datasheets express this as single-turn resolution plus revolution bits. A 25-bit SSI multiturn encoder, for example, is commonly 13 bits per turn (8,192 steps) plus 12 bits of revolutions (4,096 turns). Unlike an incremental device, which only emits pulses relative to a start point, an absolute position encoder needs no homing routine after a power cycle. The wider device family is summarized under rotary encoder, and the industrial rotary encoder category adds housings, shafts, and interfaces built for factory use.

Single-turn vs multi-turn encoder: what is the difference?

A single-turn encoder repeats its code every 360°, so it can only identify angle within one revolution. A multi-turn absolute shaft encoder adds a revolution counter, which extends the unambiguous range across many turns. On a leadscrew, a belt-driven gantry, or a geared robot joint, the axis often travels dozens of motor revolutions between end stops, so single-turn data alone is ambiguous. When the travel fits inside one turn, a simpler single-turn absolute rotary encoder is cheaper and removes the backup question entirely. Many engineers overspecify here. Checking real travel in motor revolutions takes minutes and can save real money.

Why does a lost revolution count cause real damage?

A revolution counter without backup is like a bookmark that falls out whenever you close the book: the text is still there, but you no longer know the page. On commissioning visits, a recurring pattern is a multiturn absolute encoder that works perfectly on the bench and fails only after a weekend shutdown, when someone moves an axis by hand. Why do teams miss this? Because bench tests rarely include an unpowered movement phase. Of course, some systems re-home on every start by design, and for them the backup question matters less. Safety-related functions need a separate assessment by a qualified functional-safety engineer; nothing in this article is a safety guarantee.

Battery backup in multiturn absolute encoders: principle, life and trade-offs

Battery backup keeps a low-power counting circuit alive from a small primary cell, usually lithium, so a multi turn absolute rotary encoder continues to register revolutions while the main supply is off. It is mature and supports high single-turn resolution, but it adds a maintenance item and a failure mode.

How does battery backup work in a multi turn absolute rotary encoder?

When external power drops, a changeover circuit moves the sensing and counting electronics onto the cell. To save energy, the encoder samples shaft position at a low duty cycle, so the speed it can follow during backup is far below its normal operating speed. Some designs put the cell inside the encoder; others place it in the drive or controller and feed a backup line through the cable. Both share one weakness. If the cell is depleted or disconnected while the shaft moves, the count is gone. Drives therefore usually raise a battery-low warning, and a few block motion until the axis is re-referenced.

How long does an encoder backup battery last?

There is no single honest number. Life depends on cell capacity, ambient temperature, the encoder's backup current, and the share of time the machine is off. A one-shift machine spends far more hours per year in backup than a three-shift line does. Lithium primary cells have low self-discharge, but heat shortens life. As a planning rule, treat the cell as a scheduled consumable, tie replacement to the preventive-maintenance calendar, and confirm that the swap procedure keeps the encoder powered so the count survives. That last detail is where many plants slip.

Where does battery backup still make sense?

Battery backup remains sensible when the application needs the highest single-turn resolution, tolerates scheduled maintenance, or is cost-sensitive at volume. It is also practical when existing drives and cables already provide a battery supply line to the multi turn absolute rotary encoder. The drawbacks are logistics: lithium shipping rules, spare-cell shelf life, and technicians who forget the task. For sealed or hard-to-reach installations, such as a robot joint or rotating stage, opening the housing for a cell swap can cost more than the encoder.

Energy harvesting: how a Wiegand multiturn encoder and magnetic sensing work

Energy harvesting generates the tiny amount of energy needed for revolution counting from the rotation itself, so no battery is required. The most common implementation is a Wiegand multiturn encoder, which pairs a rotating magnet with a Wiegand wire. Each magnetic reversal produces a short voltage pulse strong enough to power a low-energy counter and nonvolatile memory write.

Do multi turn absolute encoders need batteries?

No. A battery-free multiturn encoder can be built with energy harvesting or with purely mechanical gearing, so a battery is one option rather than a requirement. In a Wiegand wire, a specially processed ferromagnetic wire with a hard shell and soft core, the pulse appears when the local magnetic field flips past a threshold. Its amplitude is largely independent of how slowly the shaft turns. That property lets a harvesting multi turn absolute rotary encoder register turns even when the shaft is nudged by hand during a shutdown. The pulse energy is small, so the design must fit sensing, counting, and memory write inside that budget.

How does a magnetic multiturn encoder count turns?

A magnetic multiturn encoder typically combines a magnetic single-turn sensor, such as Hall or magnetoresistive elements reading a magnetized disc, with a multiturn stage. That stage may be Wiegand-based, or it may use a reduction gear carrying magnet wheels. In normal operation the main supply powers everything and the device outputs absolute position. After a supply failure, the harvesting stage records each turn event; at restart, the electronics combine the stored count with the single-turn angle. Magnetic sensing generally tolerates oil, dust, and vibration better than glass-disc optics, though stray fields near large motors or brakes call for attention during mounting.

What are the limits of energy harvesting?

Harvesting is not magic, and the limits deserve plain language. The counting stage is a coarse event detector, so precision still comes from the main single-turn sensor. Reliability at high unpowered shaft speeds depends on the design and its datasheet limit, and a hard shock or strong external field can, in rare cases, cause missed or false events. Counting range is also finite, commonly 12 to 16 bits of revolutions. Manufacturer test reports, not marketing claims, should settle these points.

Gear-driven and optical routes to battery-free revolution counting

Gear-driven and optical designs are the other main routes to a battery-free multiturn encoder, and they are mechanical rather than energy-harvesting. A reduction gear train turns additional code discs, and optical or magnetic sensors read them. The count is stored as the physical angle of the gears, so retention needs no electrical energy at all.

Gear-driven multiturn encoder

In a gear-driven multiturn encoder, each stage divides speed by a fixed ratio, so a 12-bit design needs enough stages to span 4,096 turns. Position is read at power-up straight from the gear angles, and nothing electrical can run flat. The price is mechanical: longer housings, more bearings, a ceiling on maximum speed, and a small amount of backlash that error budgets sometimes overlook. It is the classic choice for slow, heavy, high-reliability axes such as cranes, valves, and large positioning stages.

Optical multiturn absolute encoder

Optical sensing offers very high single-turn resolution because fine grating patterns can be read precisely. Many optical multiturn absolute encoder products pair an optical single-turn disc with a gear-driven multiturn stage; others rely on battery backup for counting. The label "optical" therefore tells you how angle is read, not how revolutions are stored. Ask the supplier which method keeps the count. Optical units are sensitive to contamination and condensation unless well sealed, but clean assembly and robust sealing narrow that gap.

Technical comparison of energy harvesting and battery backup

Energy harvesting wins on maintenance and lifecycle simplicity, battery backup on resolution flexibility and maturity, and gear-driven designs on zero-energy retention at the cost of size. The table below summarizes the trade-offs qualitatively, because exact limits vary by model and must be taken from datasheets.

Side-by-side comparison

CriterionBattery backupEnergy harvesting (Wiegand / magnetic)Gear-driven (mechanical)
Energy source when unpoweredPrimary lithium cellPulses from shaft motionNone; gear angle stores count
Routine maintenanceScheduled cell replacementNone for countingNone for counting
Typical failure modeDepleted or disconnected cell loses countMissed event from shock, strong field, or excess speedGear wear, backlash
Very slow unpowered rotationDepends on sampling intervalPulse amplitude largely speed-independentFully independent
Housing lengthCompactCompactLonger for more turns
Battery shipping and disposalAppliesNot applicableNot applicable
Relative cost tier (indicative, not a quote)$ to $$$$$$ to $$$

Source: general engineering characteristics from manufacturer application notes and the encoder literature; verify against the datasheet of any specific model.

Industry application guidance repeatedly makes one point: an absolute encoder's value lies in knowing position immediately at power-up, so any scheme that can silently lose the revolution count undermines the reason for choosing it. (Paraphrased summary of common manufacturer application-note guidance.)

Resolution and revolutions count

Encoder resolution and revolutions count are specified separately, and both must be adequate. The values below are simple powers of two, so they describe code size, not accuracy.

Code sizeNumber of valuesMeaning
12-bit single-turn4,096About 0.088° per step
13-bit single-turn8,192About 0.044° per step
16-bit single-turn65,536About 0.0055° per step
12-bit multi-turn4,0964,096 revolutions
16-bit multi-turn65,53665,536 revolutions
13 + 12 bits combined (25-bit)33,554,4328,192 steps × 4,096 turns

A worked example makes this concrete. A leadscrew with 0.2 in pitch and 40 in of travel needs 200 shaft revolutions, so a 12-bit counter (4,096 turns, roughly 819 in) leaves a generous margin. Size the revolution range for the worst case, including gear ratios, and then pick the technology.

SSI and fieldbus interfaces

Power-off retention is independent of the interface, but the interface shapes integration. An SSI multiturn encoder sends position over a clocked RS-422 link, which is simple, deterministic, and common on retrofits. A fieldbus absolute encoder using EtherCAT, PROFINET, or CANopen adds diagnostics and configuration, which helps with battery-health alarms, preset commands, and revolution-range scaling. CANopen devices typically follow the CiA 406 encoder profile, and BiSS-C is another widely used serial option. Whichever you pick, confirm how the multi turn absolute rotary encoder flags a lost count after power-up and whether your controller reads that flag.

How to choose and validate: a step-by-step procedure

Choose by working backward from the failure you cannot accept: define travel in motor revolutions, unpowered movement risk, maintenance access, and interface, then match the technology. The ordered steps below reflect common commissioning practice for any multi turn absolute rotary encoder.

Selection steps

  1. Calculate total travel in shaft revolutions, including gear ratios, and add margin so the revolution range (for example 12 bits, 4,096 turns) is never exceeded.
  2. Judge whether the shaft can move while the machine is off, through gravity, brake release, hand-jogging, or transport.
  3. Estimate the maximum speed of that unpowered movement and compare it with the datasheet limit for backup or harvesting mode.
  4. Decide whether scheduled cell replacement is acceptable at that location and for that maintenance crew.
  5. Check mounting space, shaft load, temperature, oil exposure, vibration, and stray magnetic fields near motors and brakes.
  6. Match the interface (SSI, BiSS-C, EtherCAT, PROFINET, CANopen) and confirm how the controller handles a lost-count flag.

Commissioning and power-loss test

  1. Home the axis, then record the reported absolute value and a physical reference mark.
  2. Remove all power to the encoder, including any drive-side backup supply you plan to rely on.
  3. Rotate the axis several full turns in both directions at the highest realistic unpowered speed.
  4. Restore power and compare the reported position with the physical mark; the revolution error should be zero.
  5. Repeat after a long dwell, and for battery designs also after a simulated low-cell condition and a cell swap.
  6. Document the results and set a maintenance interval or inspection trigger.

Common mistakes

Three errors recur. Engineers compare single-turn resolution but ignore revolution bits. They test power loss without moving the shaft. And they assume a "battery-free" label removes every limit, when speed and shock ratings still apply. Even the best harvesting multi turn absolute rotary encoder needs clean mounting, a correct magnet air gap, and properly shielded cable. None of this is exotic, yet these details decide field results more often than the headline specifications.

Application cases and supplier considerations for 2026

The right choice depends on axis type, service access, and environment rather than on one technology winning everywhere. The first two cases are illustrative; the third and the supplier details come from a manufacturer's own description and are not independently verified.

Case 1: vertical machine-tool axis

On a vertical head axis, gravity can pull the axis down when the brake releases, so a lost count carries immediate crash risk. A battery-free multi turn absolute rotary encoder removes dependence on a backup cell, though the controller should still verify position at startup. In job-shop retrofits, adding a battery module is often the first fix and a regret later, when the cell dies unnoticed. Where the cell is easy to reach and monitored by the drive, battery backup is still workable.

Case 2: humanoid and service robot joints

Robot joints are compact, sealed, and hard to service, which argues against replaceable cells. A compact magnetic multiturn encoder fits well, but motor-driver EMI and shock loads demand testing. The manufacturer discussed below says it works with humanoid robot companies, including Leju Robotics, on encoder applications.

Case 3: custom encoders for aerospace use

The same manufacturer states that it co-developed a custom multi turn absolute rotary encoder with an aerospace research institute for a satellite attitude-adjustment system. Technical details are not public. As a general engineering principle, not a statement about that product, designers avoid consumables where service is impossible.

What to ask a supplier

Request test evidence for temperature, EMC, and ESD; documented counting limits; interface options; and written warranty terms. The manufacturer in the cases above reports 60-plus self-developed intellectual-property items, core components using iC-Haus chips, and ISO 9001, CE, and RoHS certification. It also cites a plant of about 11,000 m² (roughly 118,000 sq ft), including a 2,000 m² (roughly 21,500 sq ft) class-100,000 cleanroom for grating production, and annual capacity above 1.2 million units. It says it has supplied encoders, handwheels, and couplings to Haas and helped develop spindle encoders with a machine-tool maker as a substitute for imported products. Treat all of this as company-stated until confirmed by a sample evaluation or audit. Its published terms mention both an 18-month warranty and a lifetime warranty, so ask for the exact written wording.

Final recommendation

For most new 2026 designs where axes can move unpowered and service access is limited, a battery-free multi turn absolute rotary encoder, based on energy harvesting or gearing, is the safer default. Battery backup remains a rational option for high-resolution, cost-driven, easily serviced axes. Whichever you choose, verify power-loss behavior by test, document the revolution range, and assess any safety function separately.

Frequently asked questions

Q: Is a battery-free multiturn encoder always better than battery backup?

A: No. Battery-free designs remove cell maintenance and suit sealed or hard-to-reach axes, but battery backup can offer higher single-turn resolution and lower unit cost. The better choice depends on travel, unpowered shaft speed, service access, and budget, so compare datasheet limits and run a power-loss test.

Q: Can a Wiegand multiturn encoder count when the shaft moves slowly while unpowered?

A: Generally yes, because Wiegand pulse energy is largely independent of rotation speed. The practical limits are the maximum unpowered speed, shock, and stray magnetic fields stated in the datasheet. Confirm these limits with the supplier and verify them in a bench test before release.

Q: What revolutions range does a multi turn absolute rotary encoder need?

A: Convert total axis travel into shaft revolutions, including any gear ratio, then add margin. A 12-bit counter covers 4,096 turns and a 16-bit counter covers 65,536 turns. With a 0.2 in leadscrew pitch, 12 bits spans roughly 819 in of travel.

Q: Does the fieldbus change how the revolution count is stored?

A: No. EtherCAT, PROFINET, CANopen, and SSI only transmit position data; the count is stored inside the encoder by battery, harvesting, or gearing. The fieldbus does improve diagnostics, such as lost-count or low-battery flags, so check that your controller reads them.

Key words:

multi turn absolute rotary encoder


ONLINE MESSAGE

Please fill in the information accurately and keep your communication channels open. We will contact you as soon as possible

Submit

ONLINE MESSAGE

Please fill in the information accurately and keep your communication channels open. We will contact you as soon as possible

Submit